In the selection of furniture, hand-made furniture is still very popular among consumers. When hand-made furniture, the selection of plates becomes a crucial step. There are many kinds of wood used to make furniture. The difference between price and quality is very large and the scope is very wide. It is suitable for different kinds of consumers to choose. The use of furniture plates, the most basic is to see how the environmental performance of the plate, this issue can not be ignored. Secondly, we must also pay attention to what kind of plate is used for furniture . It is easy to be deformed and the moisture content is up to the standard. Untreated plates are the best and most suitable for use. Here are just a few of the common types and characteristics of plates used in furniture production to help you further understand what plates to use for furniture .
What kind of plate is good for furniture?
1. Wood board (commonly known as Daxin board)
Wood board (commonly known as the big core board) is a Plywood with a solid wood core, and its vertical (differentiated by the direction of the core sheet) has poor flexural compressive strength but high transverse bending resistance. Most of the current market is solid, rubberized, double-sided sanding, five-layer Blockboard , is one of the most commonly used plates in the current decoration.
Personal opinion: In fact, in the better quality of the wood board, the environmental protection coefficient is also guaranteed, but the cost is also high. With the subsequent painting and other processes, it will more or less change an environmentally friendly product. Not so environmentally friendly. Under normal circumstances, in the furniture room made of wood panels, it must be more ventilated and breathable, it is best to leave for a few months before moving in.
Particleboard is the process of cutting all kinds of shoots, trails, fast-growing wood, sawdust and other materials into pieces of certain specifications. After drying, it is mixed with rubber, hardener, waterproof agent, etc., and pressed at a certain temperature and pressure. A type of wood-based panel, which has a honeycomb-like profile, is called a Particle Board .
Adding certain materials such as “moisture-proof factor†or “moisture-proof agent†to the interior of the particle board has become the moisture-proof particle board normally referred to by people. It is also referred to as moisture-proof board for short. It has a certain moisture-proof effect because the particle board itself has a certain moisture resistance and absorbs water. After the copy has a small expansion coefficient, it is commonly used in cabinets, bathroom cabinets and other environments, but in reality, it has become a tool for many inferior particle boards to cover up more internal impurities. The addition of green stains to the interior of the particle board creates what is currently referred to as green-based chipboard in the market. Many manufacturers use it to mislead green boards. There is no scientific basis. Domestic and foreign top brands of particleboard in fact more than the base material.
3. Fiberboard
When some businesses say that they are high-density panel production cabinets, it may be necessary to weigh the weight of the panels per unit area according to the above density standards, and see if the degree of density is not a high-density board, or whether it is treated as medium-density board. High-density board sales, this approach may affect the interests of some businesses, but from the point of view of integrity business to promote themselves is a high-density board will not be afraid of customers to verify.
4. Solid finger board
Fingerboard, also known as integrated board, glulam, and finger joint material, is a piece of solid wood small pieces that have been processed and processed like a “fingerâ€. Because of the zigzag interface between boards, similar to two fingers Cross docking, so called finger board. Since the raw wood strips are cross-linked, such a combined structure has a certain binding force, and since there is no need to stick the surface plate up and down, the glue used is extremely small.
Previously, we had used camphor wood fingerboards as cabinet backboards and even sold them as a selling point. However, there were indeed some cracks and deformations that appeared in later use, so they were later cancelled. Beech wood is used as a backboard for cabinets. Here, I would like to remind customers who want to use fingerboards to make cabinet furniture. They must carefully select the plates and negotiate with the producers on the possible occurrence of cracking, deformation, etc. in the later period, regardless of whether they are businessmen or individuals. It is said that after the first thing, it will not be confused, and after the communication is completed, the troubles will be less.
5. Particle board
The so-called solid wood particle board is in fact a board produced by a chipboard process and is a kind of particle board that belongs to a homogeneous particle board.
The scientific name of the homogeneous particleboard is directional structure particleboard. It is a kind of material with small diameter, thinning material, wood core, board skin, branch material, etc. Processed and grown by special equipment 40mm, 70mm, width 5mm, 20mm, thickness 0.3mm, 0.7 The flaky pieces of mm, after drying, sizing, and special equipment, the core plywood pieces are arranged in a criss-cross pattern, and then the man-made board after the hot press forming. The large sub-homogeneous particle board will use the advanced single-channel drying machine to dry the fins. The expansion coefficient is small and the moisture resistance is very good. The fins are oriented with layered pavement, so its internal internal texture is uniform. Ordinary particle board and powdered MDF have strong nail holding force, bending resistance and stability.
6. Multi-layer solid wood board
The multi-layer solid wood board is made of multi-layer plywood arranged in a criss-cross pattern, and the surface is made of high-quality solid Wood Veneer or technical wood as a fabric, and is manufactured through several processes such as cold pressing, hot pressing, sanding, and health care. Because the multi-layer solid wood panel has the characteristics of non-deformation and good performance in adjusting the indoor temperature and humidity, the surface layer wood Veneer material has natural and real wood texture and feel, so the selectivity is stronger. Therefore, it is greatly favored by consumers.
Multi-layer solid wood panels have good structural stability and are not easily deformed. Due to the vertical and horizontal gluing, high temperature and high pressure, the deformation of the solid wood plate is solved in terms of internal stress. In the production process, the use of self-made high-quality environmental protection rubber, so that the product's formaldehyde release limit to meet the national standards, green environmental protection.
7. Laminate, not easily deformed
This is a new type of solid wood material, using high-quality imported large-diameter logs, deep processing and imaging the fingers as staggered spliced ​​wood. Due to different processes, the environmental performance of this kind of board is superior. It is 1/8 that the large core board allows the amount of formaldehyde, and the price is about 200 yuan each, which is slightly more expensive than the high-grade big core board.
But on the other hand, this type of wood made from American spruce and other solid wood can be painted and brushed directly, eliminating the need for a process compared to a large core board. Finally, the cost of construction may be flat.
8. The MDF is inferior to the chipboard gripping force
Particleboard is a natural material that is crushed into pellets and then pressed into plates. The medium density board is formed by pressing wood chips and has good flatness but poor moisture resistance.
In contrast, the density of the MDF is lower than that of the chipboard. If loosening occurs after the screw is tightened, the strength of the MDF is not high enough to fix it. Therefore, it is rarely used as a cabinet.
9. Decorative plywood saves money and is cheap
Multilayer boards, also known as plywood and plywood, have different layers. According to the thickness of 3-9 cm, it can also be called 3-9 PCT board. Its advantages and disadvantages mainly depends on the raw materials. The price of Liu'an cores for each 1.2m??.4m plate is 10-20 yuan. The mahogany and poplar will be cheaper.
At present, the main use in home improvement is a decorative plywood, that is, a very thin solid wood veneer has been attached to the plywood in the factory. The decorative plywood is easy to use and the price is cheaper than buying the veneer panel for the construction team.
10. Melamine double board, not afraid of water and fire
This board is shiny on both sides, very hard, not afraid of water and fire, mainly used in furniture and cabinets. The price is more expensive, 1.2m??.4m specifications of the board from 80 to 140 yuan per sheet.
11. Decorative panels, manufacturing and solid wood effect
The veneer is veneer peeled with high-grade wood with obvious wood grain. The veneer is very thin, the thinnest is only 0.3mm, and the thickness is only 2-3mm. The color of common veneer is from light to dark, with dozens of cherry, maple, white peony, red peony, ash, white oak, red oak, teak, rosewood, walnut, white shadow wood, red shadow wood, etc. The varieties are expensive.
For large areas, it is best to buy veneer plywood directly. If the panel is to be used locally for unique effects, a higher process is required.
12. Buy wood with treated moisture content and treated wood
When the moisture content of wood is higher than the equilibrium moisture content of the environment (the annual average moisture content in Beijing is 11.4%), the wood will shrink dry, otherwise it will absorb moisture and expand. The main reason for the cracking and deformation of wood is that the moisture content is too high or too low. Qualified wood needs to go through the factory's high-temperature cooking and drying procedures to finally reach the local moisture level. Therefore, the moisture content of wood is particularly important.
Do not plan to be cheap. Materials that are sold at a low price are usually materials that are crudely manufactured and formaldehyde is severely exceeded. It is best to purchase in the formal market, where the purchase channels are more secure. Buy branded materials. Since wood is the main material in home decoration, the number of purchases is large, and care should be taken when buying. It is best to go with experienced people or professional buyers. Can also commission the decoration company to buy, first, they have a stable quality supplier, the price may be lower, and second, once the quality problems, the responsibility is clear, the problem is resolved.
Editor's summary: The above is the shopping guide: What kind of furniture to do a good plate is a piece of furniture can not be ignored to buy the core of the relevant introduction, hand-made furniture on the one hand can meet the different needs of different consumers, on the other hand, you can also Choosing the preferred plate to customize the unique furniture for yourself. There are many types of plates used to make furniture. Each has its own characteristics and advantages. No matter which one, it can be achieved through reasonable production. Good use effect.
Furniture plate to do the cabinet with what plate to do a good tatami what kind of plate good scenery furniture wardrobe what plate
Engineering Veneer is a thin sheet of wood, rotary cut, sliced or sawed from expensive natural wood. The veneer is easy to be edge jointed and overlaid on plywood, MDF, particleboard and so on. So, it can be used in fancy plywood, fancy MDF, fancy blockboard and veneer faced particle board.We have Natural Engineering Veneer and Engineering Fancy Veneer
Luli Group Co., Ltd, also supply engineered wood veneers with good quality and competitive pricing.
Advantages of using veneers:
Compared to wood, one of the primary advantages of using veneer is stability. While solid wood can be prone to warping and splitting, because veneer is made of thin layers of wood glued together, the chances of splitting or cracking are reduced. Further, the glue used provides additional strength, making the end result stronger than natural wood.
Usages of Veneer:
Used to cover the surface of plywood, MDF, chipboard, blockboard and so on.
Specification details:
Sizes: 1220mm x 2440mm, 1250mm x 2500mm or as your request
Thickness: From 0.15mm to 0.6mm or as per request
Species: Okoume, Bintangor, Terminalia, Red hardwood, etc.
Grade available: A/A, A/B, B/B
Cutting way: Rotary cutting
Engineering Veneer
Engineering Veneer,Natural Engineering Veneer,Engineering Fancy Veneer,Engineered Wood Veneer
Luli Group Co.,Ltd. , https://www.cnluli.com