| Home>Bearing knowledge>Features of joint bearings |
Joint bearing features
Source: China Bearing Network Time: 2018-01-08
| /*250*250 was created on 2017/12/25*/ var cpro_id = 'u3171089'; |
.2) GE...ES single-slit outer ring; smooth oil groove. Can accept radial load and small axial load in either direction.
.3) GE...ES-2RS single-slit outer ring; smooth oil groove; sealing ring on both sides. Can accept radial load and small axial load in either direction.
.4) GEEW...ES-2RS single-slit outer ring; smooth oil groove; sealing ring on both sides. Can accept radial load and small axial load in either direction.
.5) GE...ESN single-slit outer ring; smooth oil groove; outer ring with stop groove. Can accept radial load and small axial load in either direction, but axial load is accepted by the stop ring; It can only reduce its axial load.
.6) GE...XSN double-slit outer ring (split outer ring); smooth oil groove; outer ring with stop groove. Can accept radial load and small axial load in either direction. When the retaining ring is accepted; it can only reduce its axial load.
.7) GE...HS inner ring has a smooth oil groove; double semi-outer ring; the clearance can be adjusted after wear. It can accept radial load and small axial load in either direction.
.8) GE...DE1 inner ring is hardened bearing steel; outer ring is bearing steel. Kneading is formed during inner ring installation; smooth oil groove and oil hole. Bearing with inner diameter less than 15mm; no smooth oil groove and oil hole. Can accept radial loads and small axial loads in either direction.
.9) GE...DEM1 inner ring is hardened bearing steel; outer ring is bearing steel. Kneading is formed when the inner ring is installed; after the bearing is installed in the bearing seat; the end groove is pressed out on the outer ring to fix the bearing axially. Can accept radial loads and small axial loads in either direction.
.10) GE...DS type outer ring has mounting groove and smooth groove. It is limited to large-scale bearings. It can accept radial load and small axial load in either direction (the side of the mounting groove cannot accept axial load).
2. The angular contact joint bearing GAC...S type inner and outer rings are hardened bearing steel; the outer ring has oil groove and oil hole. It can accept radial load and one direction axial (combined) load.
3. The thrust joint bearing GX...S type shaft ring and seat ring are hardened bearing steel, the seat has oil groove and oil hole. It can accept axial load or combined load in one direction (at this moment, the radial load value should not be greater than the axial load) The value is 0.5 times).
4. Rod end joint bearings.1) SI...E type is the assembly of GE...E type bearing and rod end. The rod end has internal thread; the data is carbon structural steel, no smooth oil groove. It can accept radial load and less than either direction. Or equal to 0. 2 times the axial load of the radial load.
.2) SA...E type is the assembly of GE...E type bearing and rod end. The rod end is externally threaded; the data is carbon structural steel, no smooth oil groove; can accept radial load and less than or equal to 0 in either direction. Axial load of 2 times radial load.
.3) SI...ES type is the assembly of GE...ES type bearing and rod end. The rod end is internally threaded; the data is carbon structural steel with smooth oil groove. It can accept radial load and less than or equal to 0 in either direction. Axial load of 2 times radial load.
.4) SA...ES type is the assembly of GE...ES type bearing and rod end. The rod end is externally threaded; the data is carbon structural steel with smooth oil groove. It can accept radial load and less than or equal to 0 in either direction. Axial load of 2 times radial load.
.5) SIB...S type rod end with internal thread; data is carbon structural steel, inner ring is hardened bearing steel, smooth oil groove. Can accept radial load and any direction less than or equal to 0. 2 times radial The axial load of the load.
.6) SAB...S type rod end with external thread; data is carbon structural steel, inner ring is hardened bearing steel, smooth oil groove. Can accept radial load and any direction less than or equal to 0. 2 times radial The axial load of the load.
.7) SQ... is a ball-end rod end joint bearing; the rod end is carbon structural steel, the ball head is carburized steel. It can accept radial load and small axial load in either direction.
5. Self-smoothing radial joint bearing. 1) GE...C type and GE...T type kneading outer ring; outer ring sliding surface is sintered bronze composite material, inner ring is hardened bearing steel; sliding outer surface is plated with hard chrome. The bearing of the scale. The outer ring is the bearing steel; the sliding outer surface is a layer of PTFE fabric, the inner ring is hardened bearing steel; the sliding outer surface is plated with hard chrome. It can accept the direction constant load; together with the radial load Can accept small axial loads in either direction.
.2) GE...CS-2Z outer ring is bearing steel; sliding outer surface is sintered bronze composite material, inner ring is hardened bearing steel; sliding outer surface is plated with hard chrome, both sides with dust cover. Can accept direction unchanged Load; accepting radial loads together can accept smaller axial loads in either direction.
.3) GEEW...T-type outer ring is bearing steel; sliding outer surface is a layer of PTFE fabric, inner ring is hardened bearing steel; sliding outer surface is plated with hard chrome. It can accept the same direction load; The load together can accept a small axial load in either direction.
.4) GE...F type outer ring is hardened bearing steel; sliding outer surface is glass fiber reinforced plastic with PTFE as additive, inner ring is hardened bearing steel; sliding surface is hard chrome plated. Medium radial load.
.5) GE...F2 type outer ring is glass fiber reinforced plastic; sliding outer surface is glass fiber reinforced plastic with PTFE as additive, inner ring is hardened bearing steel; sliding surface is hard chrome plated. Medium radial load.
.6) GE...FSA outer ring is medium carbon steel; sliding outer surface is composed of glass fiber reinforced plastic disc with PTFE as additive; fixed on the outer ring with fixing device, inner ring is hardened bearing steel. For large and extra large bearings. Can accept large radial loads.
.7) GE...FIH type outer ring is hardened bearing steel, inner ring is medium carbon steel; sliding outer surface is composed of glass fiber reinforced plastic disc with PTFE as additive; fixed on the inner ring with fixing device, Double and half outer ring. For large and extra large bearings. Can accept large radial loads.
6. The self-smooth angle touch joint bearing GAC...F type outer ring is hardened bearing steel, the sliding outer surface is glass fiber reinforced plastic with PTFE as additive, the inner ring is hardened bearing steel; the sliding outer surface is plated with hard chrome. Acceptable Radial load and axial (combined) load in one direction.
7. The self-smooth thrust joint bearing GX...F type seat is hardened bearing steel; the sliding outer surface is glass fiber reinforced plastic with PTFE as additive; the shaft ring is hardened bearing steel; the sliding surface is hard chrome plated. It can accept one. Axial load or combined load in the direction (the radial load value at this moment shall not be greater than 0.5 times the axial load value).
8. Self-smooth rod end joint bearings.1) SI...C type is the assembly of CE...C type bearing and rod end. The rod end is internally threaded; the data is carbon structural steel. It can accept the direction constant load. The load can together accept axial loads in either direction less than or equal to 0. 2 times the radial load.
.2) SA...C type is the assembly of CE...C type bearing and rod end. The rod end is externally threaded; the data is carbon structural steel. It can accept the load with the same direction. It can accept the radial load together. A direction less than or equal to 0. 2 times the axial load of the radial load.
.3) SI...CS-2Z is ​​the assembly of GE...CS-2Z bearing and rod end. The rod end is internally threaded; the data is carbon structural steel. It can accept either direction less than or in combination with radial load. Axial load equal to 0. 2 times radial load.
.4) SA...CS-2Z is ​​the assembly of GE...CS-2Z bearing and rod end. The rod end is externally threaded; the data is carbon structural steel. It can accept the direction constant load. Under the radial load Together, it can accept axial loads in either direction less than or equal to 0. 2 times radial load.
.5) SIB...C rod end with internal thread; data is carbon structural steel; sliding outer surface is sintered bronze composite material, inner ring is hardened bearing steel; sliding outer surface is plated with hard chrome. can accept radial direction unchanged Load.
.6) SAB...C rod end with external thread; data is carbon structural steel; sliding outer surface is sintered bronze composite material, inner ring is hardened bearing steel; sliding outer surface is plated with hard chrome. can accept radial direction unchanged Load.
.7) SIB...F rod end with internal thread; data is carbon structural steel; sliding surface is made of glass fiber reinforced plastic with PTFE as additive, inner ring is hardened bearing steel; sliding surface is hard chrome plated Can accept radial loads with constant direction.
.8) SAB...F rod end with external thread; data is carbon structural steel; sliding surface is made of glass fiber reinforced plastic with PTFE as additive, inner ring is hardened bearing steel sliding surface with hard chrome plating. Can accept radial load with constant direction.
.9) SQ...L type is made of special self-smooth alloy material; it can accept radial load and small axial load in either direction.
Recommend to friends comments close window
| Bearing related knowledge |
| Bearing information (1) Transmission one-axis rear bearing damage view fault detection method to repair the thrust of the NSK bearing's primary skill bearing product heating flange bearing |
This article links to http://
Please indicate the bearing network http://
Previous: Bearing rear code comparison to clarify the next series: the need for bearing data
Zinc coating is a type of protective coating that is commonly used on metal surfaces to extend their durability and prevent them from corroding or rusting. It involves the application of a thin layer of zinc onto the surface of metal parts through a number of processes, the most common of which is hot-dip galvanizing.
The benefits of zinc coating are many. It offers excellent corrosion resistance, making it ideal for outdoor applications where metal parts are exposed to harsh weather conditions. Zinc coating also provides a smooth and uniform finish, which enhances the appearance of the metal and makes it more visually appealing. In addition to this, zinc coating improves the overall performance of the metal part by increasing its resistance to wear and tear.
Zinc coating is used in a variety of industries and applications, including construction, automotive, and manufacturing. In the construction industry, it is used to protect steel structures such as bridges, buildings, and pipelines from corrosion. In the automotive industry, it is used to protect metal components such as car frames, exhaust systems, and suspension parts. In the manufacturing industry, it can be used to protect machinery and equipment parts from rust and corrosion.
In conclusion, zinc coating is a highly effective and versatile technology for protecting metal parts from corrosion and rust. Whether for outdoor or indoor applications, it offers numerous benefits in terms of performance and durability. As such, it is an essential process for enhancing the longevity and reliability of metal parts across a range of industries and applications.
Zinc Plating,Cold Galvanizing Spray,Zinc Plated Steel,Zinc Nickel Plating
Lizhi Precision Manufacturing Technology Co.,Ltd , https://www.lizhipartsmfg.com