High-temperature heat transfer oil Pump is a single-stage cantilever structure divided into foot support and center support, the pump inlet is axial suction, the outlet is centered vertically upward. The pump and drive motor are mounted on the same base with flexible couplings. The entire unit without adding cold system. High-temperature heat transfer oil pump structure is reasonable, excellent performance, reliable use. Suitable for conveying high temperature liquids without solid particles. The degree of corrosion resistance and service temperature depends on the material of the main part that is in contact with the medium. In addition, RY series of heat transfer oil pump is also widely used in machinery industry, food industry, pharmaceutical production, hot oil furnace fuel supply circulation system, hot oil heating circulation system. Advantages and features: High-temperature heat transfer oil pump technology is advanced, high efficiency, long-term stable operation in the hot state no leakage, no additional cooling system, the use of safe and reliable and other characteristics in China heating medium heating system has been widely used, has been RY series of air-cooled high-temperature heat-conducting oil pump is mainly used for conveying weakly corrosive high-temperature liquid without solid particles, the use of temperature ≤ 370 ℃, is an ideal circulating pump. The thermal oil pump widely used in high temperature paper lunch box stereotypes, dynamic vulcanized tire and reclaimed rubber machinery, flat vulcanization, rubber, drying, feed drying, printing and dyeing, chemical industry, plywood production, waterproofing membrane production, asphalt heating, noodle drying industry. (1) The high-temperature heat-conducting oil pump is the second-generation product developed on the basis of digestion and absorption of foreign oil pumps. The basic structure is a single-stage single-suction cantilever foot support structure. The inlet of the hot oil pump is axial suction and the outlet is centered vertically upward. And the same motor mounted on the base. (2) The RY-type heat-conducting oil pump is supported by a double-ended ball bearing structure. The front end is lubricated with grease and the rear end is lubricated with grease. The middle part has a guide pipe for observing the sealing and recovering the heat-conducting oil at any time. (3) RY series air-cooled high-temperature heat-conducting oil pump adopts self-heating and heat-dissipating structure, which changes the traditional water cooling structure, which makes the structure simple, small in size, saves operation cost, good performance and reliable operation. (4) RY series of air-cooled high-temperature heat-conducting oil pump with packing seal and mechanical seal combination form, packing seal with high temperature filler, has good thermal adaptability, and mechanical seal is the use of high mechanical strength, wear resistance Good cemented carbide material, to ensure the sealing performance under high temperature conditions. (5) RY series air-cooled high-temperature heat-conducting oil pump uses the third generation of polytetrafluoroethylene (referred to as PTFE) lip seal, the sealing performance has been a leap forward than the rubber seal reliability increased by 25 times the corrosion resistance . The heat-conducting oil pump adopts the self-heating and heat-dissipating structure to change the traditional water-cooled structure, which makes the structure simple, small in size and economical in operation cost, good in performance and reliable in use. It is the second generation product developed on the basis of digestion and absorption of foreign oil pumps in our country. Structure for the single-stage single-suction cantilever foot support structure, the pump inlet for the axial suction, the outlet for the center vertical upward, and the same motor mounted on the base. RY series of heat transfer oil pump mainly consists of shell, rotor, bearings, seals and other components, the use of packing seal structure, additional temperature oil seal, the role of secondary seal. Pump and motor with three claw-type flexible coupling. RY series of heat transfer oil pump The pump from the design to change the traditional hot oil pump structure, the use of natural cooling cooling, reducing the pump size, so that the structure is simple, saving running costs, safe and reliable.
Garden tools are maintenance equipment for human green landscapes. They are used to maintain lawns, hedges, and protect flowers and trees, replacing most of the mechanized tools represented by manual labor. Classified according to use occasions, garden tools include garden tools and garden tools. According to the classification of the objects of use, it can also be divided into household tools and professional tools.
Trees Hedge Shear,Household Tools,Multifunctional Garden Trowel,Folding Garden Trowel
Rugao Yaou Import & Export Trade Co., Ltd , https://www.ntyaous.com