Everyone has always attached great importance to our home improvement. But for our outer walls, everyone can't ignore it. Because our outer wall accepts the baptism of the wind and rain. Therefore, the decoration of the geographical exterior wall must be especially careful. Especially our selection, as well as our construction. Below, everyone and the decoration of the small series to understand how the outer wall waterproof and moisture-proof construction? So everyone has a specific reference.
First, how to construct the external wall waterproof and moisture proof
1. Initially know that the wall inspection and treatment needs to be step by step according to the standard. Everyone knows this. If there are holes in the outer wall and unevenness, it should be treated first. It is necessary to block the various holes in the wall. If there are any phenomena such as rising mold and honeycomb surface in the outer wall, it should be removed according to the actual situation. Clean the wall.
2. Understand that our exterior wall waterproofing and waterproofing glue should be formulated in strict proportion. Construction is also important. The wall surface should be smoothed first, and the plaster should be layered with plaster. The thickness of each layer of plaster should not exceed 2cm. If it is too thick, it is necessary to set the wire mesh in the layered position.
3, there is the seam, you need to pay special attention when the outer wall is waterproof. Not only is there no benefit. Then brush the waterproof glue several times, and also need to apply around the seam. Before the exterior wall is installed, it is necessary to check the windows, doors and windows, and the water flows into the house from the gap.
Second, which brands of waterproof coatings
1, the quality is better, the number of people who use k11 general-purpose waterproof coatings are good. The composite waterproofing slurry prepared by the emulsion and the inorganic powder is obtained by polymerizing high-quality cement and selected quartz sand with a specific polymer to achieve a double waterproof effect. It features a rigid, water-repellent material that highlights the bonding properties.
2. There is also JS waterproof coating in the waterproof of the outer wall surface is a green environmental protection material. It is also very good for environmental protection. It has the advantages of environmental protection, good aging resistance, convenient construction, simple operation and strong cohesiveness. Most of JS waterproof coatings are white in color, which can provide better heat insulation effect, and can be modulated into color for roof and exterior walls. A decorative and beautifying effect, a new ideal environmentally friendly waterproof material.
3, the new material acrylic waterproof coating, construction is also very convenient. Using internationally advanced technology and raw materials, the pure acrylic polymer can be easily combined with the ground gap to form a strong waterproof layer, which is especially suitable for use as a wall waterproof material.
Everyone on our façade can't be ignored. Otherwise, there will be an unsightly scene when you have not lived for a few years. The above content can be referenced to choose our products. If you still want to continue with more renovation information, please continue to pay attention to our decoration home website. Our website will constantly update information about home improvement.
More related wonderful reading:
External wall waterproof and moisture proof method, external wall waterproof and moisture proof
The masonry bit is a variation of the Twist Drill Bit, the bulk of the Tool is a relatively soft steel, and is machined with a mill rather than ground. An insert of tungsten carbide is brazed into the steel to provide the cutting edges.
Masonry bits typically are used with a Hammer Drill, which hammers the bit into the material being drilled as it rotates; the hammering breaks up the masonry at the Drill Bit tip, and the rotating flutes carry away the dust.
Hammer drill bits often use special shank shapes such as the SDS type, which allows the bit to slide within the chuck when hammering, without the whole heavy chuck executing the hammering motion.
Masonry bits of the style shown are commonly available in diameters from 3 mm to 40 mm. For larger diameters, core bits are used. Masonry bits up to 1,000 mm (39 in) long can be used with hand-portable power tools, and are very effective for installing wiring and plumbing in existing buildings.
Hand Tool,Tungsten Carbide Masonry,Premium Carbide Drill,Concrete Drill Bits Set Drill
Behappy Crafts (suzhou)Co.,Ltd , https://www.jshaoyue.com