Home>Bearing knowledge>The reason for the shortcomings of bearing external grinding and the analysis of countermeasures

/*728*90 created on 2018/5/16*/ var cpro_id = "u3440131";

Analysis of the causes and disadvantages of bearing surface grinding

---

/*250*250 was created on 2017/12/25*/ var cpro_id = 'u3171089';

The bearing is in the grinding process; the surface of the work is ground by a high-speed rotating grinding wheel; therefore, if it is not operated and adjusted according to the operation instructions during grinding, it will present various shortcomings in the bearing operation; The overall quality of the bearing. The bearing is in the fine grinding; because the rough demand is very high; the grinding marks on the exterior of the work can often be observed with the naked eye.
The reason for presenting the traces of the interpenetrating spiral traces is mainly because the flatness of the grinding wheel is poor; there is a concave and convex appearance; during grinding; the grinding wheel and the workpiece are only slightly touched; when the workpiece or the grinding wheel reciprocates several times; The workpiece embodiment will reproduce the interpenetrating spiral and can be observed by the naked eye. The pitch of these spirals is related to the workpiece table speed and the workpiece rotation speed; together with the grinding wheel axis and the worktable rail are not parallel.
ㄒ唬┞菪咝 傻 傻 傻 饕 1. The grinding wheel is poorly trimmed; the corners are not chamfered; the coolant is not trimmed,
2. The workbench guide guides too much lubricating oil; causing the workbench to float.
3. The machine tool accuracy is not good,
4. Grinding pressure is too large.
Ǘ┞菪咝 傻 傻 傻 傻 1 1. The V-shaped guide rail is not rigid enough; when grinding, the grinding wheel is offset; only the edge of the grinding wheel and the touch of the work surface,
2. When the quarrel is repaired, the commutation speed of the workbench is unstable; the precision is not high; the trimming of the grinding wheel is slightly less,
3. The workpiece itself is poorly rigid,
4. The sand on the grinding wheel with the broken and too falling off and the iron scrap under the grinding of the workpiece are attached to the outer surface of the grinding wheel; for this purpose, the finished grinding wheel should be washed or rinsed with cooling water.
5. The dressing of the grinding wheel is not good; there are some bumps.

---

Recommend to friends comments close window

Bearing related knowledge

What are the varieties of bearings? Analyze the annealing process of high carbon chromium bearing steel The order of the SKF bearing finishing process is the cause of the shortcomings of the grinding in the grinding process BMH sensor bearing

This article links to http://
Please indicate the bearing network http://

Previous:The appearance of noise in the imported bearings and the following method: Common sense of classification of smooth oil for vehicles

Peristaltic Liquid Pump

Peristaltic Liquid Pump is a Peristaltic Pump that can distribute many types of liquids, such as water-based liquid/shampoo/sauce/chemical-based liquid, etc.
The flow rate of the Peristaltic Liquid Pump can be adjusted by the digital knob to adjust the motor speed to achieve the effect of adjusting the flow rate
The liquid only gets in touch with the Peristaltic Pump Tubing, will not cause cross-contamination. it's suitable for Liquid transfer occasions with high cleanliness requirements, Eg. : food/beverage/cosmetic/medical/biopharmaceutical...
For the Peristaltic Pump Tubing, We have different material choices for your various liquids. The standard tube is silicon tubing which conforms to the FDA certificate. Except that we also offer the Saint-Gobain imported tubing, Eg.: Norprene®A-60-F/Norprene®chemical /Pharmed® BPT... Which suitable for various chemical-based liquids

Peristaltic Liquid Pump,Polishing Peristaltic Pump,Basic Liquid Peristaltic Pump,Digital Speed Transmission Pump

Baoding Chuangrui Precision Pump Co., Ltd. , https://www.chuangruipump.com