The barrier gate controller has good intelligent determination function and high reliability, and is the preferred automatic control device in the current electric barrier gate system. The following 16 points should be noted when using the Barrier Controller:
1. The performance of the alarm function depends on the performance of the alarm probe. The user should select the alarm probe according to the actual needs of the alarm. The controller is equipped with a pyro-alarm probe when it comes out of the factory. If you do not use the alarm function, the probe will not be enough.
2. Although the controller already has anti-static and anti-lightning design, please ensure that the power supply and the chassis are well grounded to ensure that the circuit is not damaged by static electricity, lightning, and other equipment.
3. The controller should be kept clean to prevent the ingress of water or other harmful substances. Cleaning the cabinet is strictly prohibited using organic solvents.
4. Do not hot-swap wiring terminals, or electrified welding operation, welding the wiring should first unplug the corresponding wiring base.
5. When the direction of opening and closing is found to be opposite, connect the “V†and “W†terminals of the controller. Similarly, when the STOP display indicates that the direction is opposite to the actual one, adjust the wiring in the same way.
6, the remote control factory encryption encryption used, can not be interchanged. When the user needs to change, the manufacturer can change the password as required.
7. The controller can directly connect UPS uninterrupted power supply to ensure that the system can continue to work after the power failure. The system is equipped with a power-off protection device, even if the power failure system setting information and records are not lost.
8. When installing a remote controller or other additional value-added equipment, be careful not to introduce other electrical signals into the controller.
9. The number of cable cores for electric doors should not be less than 8 lines (in the past, there were 7 lines, the wiring was not very reasonable), and the middle of the door cables should not contain joints.
10, delay automatic stop function can be set according to the user's door trip, factory set to 145 seconds.
11. Try to avoid connecting the controller power supply and other high-current working devices to the same power supply. The operating current of the relay is a maximum of 7A. If you want to control a larger current device, install a more powerful relay. It is better to have a separately controlled switch from the main control power supply box.
12. When the controller fails, it should be repaired by a professional or contacted by the supplier and the manufacturer. In order to avoid the failure to expand the impact of use.
13. Do not disassemble components on the controller without permission. This may cause loss of system information or chip damage.
14, connected to the +12V terminal, is conducive to give full play to the performance of the reader, if the reader is +24V power supply, please individually equipped with a linear power supply, and a common ground with the controller. Do not introduce +24V into the controller indirectly, otherwise it will cause burnout.
15. The remote control transmitter should keep the casing well, to prevent the phenomenon of extrusion, vibration, falling, and water inflow. Pay attention to check the battery voltage and replace it if necessary. When the remote control distance is too close, the battery should normally be replaced. The battery model is KC12V-23A. The remote control should try to avoid the source of electromagnetic interference.
16. The type of the interface of the alarm probe output signal should be the relay output interface. The supply voltage should be 12-15V DC, otherwise it cannot be directly powered by this controller. Probe power consumption should be ≤ 100 mA. According to the situation on the site can be equipped with more than one probe (usually 1 - 2 is appropriate), multi-probe parallel connection. Probes. Avoid the influence of other heat sources or direct light. Use a rain cover at the top.
1. The performance of the alarm function depends on the performance of the alarm probe. The user should select the alarm probe according to the actual needs of the alarm. The controller is equipped with a pyro-alarm probe when it comes out of the factory. If you do not use the alarm function, the probe will not be enough.
2. Although the controller already has anti-static and anti-lightning design, please ensure that the power supply and the chassis are well grounded to ensure that the circuit is not damaged by static electricity, lightning, and other equipment.
3. The controller should be kept clean to prevent the ingress of water or other harmful substances. Cleaning the cabinet is strictly prohibited using organic solvents.
4. Do not hot-swap wiring terminals, or electrified welding operation, welding the wiring should first unplug the corresponding wiring base.
5. When the direction of opening and closing is found to be opposite, connect the “V†and “W†terminals of the controller. Similarly, when the STOP display indicates that the direction is opposite to the actual one, adjust the wiring in the same way.
6, the remote control factory encryption encryption used, can not be interchanged. When the user needs to change, the manufacturer can change the password as required.
7. The controller can directly connect UPS uninterrupted power supply to ensure that the system can continue to work after the power failure. The system is equipped with a power-off protection device, even if the power failure system setting information and records are not lost.
8. When installing a remote controller or other additional value-added equipment, be careful not to introduce other electrical signals into the controller.
9. The number of cable cores for electric doors should not be less than 8 lines (in the past, there were 7 lines, the wiring was not very reasonable), and the middle of the door cables should not contain joints.
10, delay automatic stop function can be set according to the user's door trip, factory set to 145 seconds.
11. Try to avoid connecting the controller power supply and other high-current working devices to the same power supply. The operating current of the relay is a maximum of 7A. If you want to control a larger current device, install a more powerful relay. It is better to have a separately controlled switch from the main control power supply box.
12. When the controller fails, it should be repaired by a professional or contacted by the supplier and the manufacturer. In order to avoid the failure to expand the impact of use.
13. Do not disassemble components on the controller without permission. This may cause loss of system information or chip damage.
14, connected to the +12V terminal, is conducive to give full play to the performance of the reader, if the reader is +24V power supply, please individually equipped with a linear power supply, and a common ground with the controller. Do not introduce +24V into the controller indirectly, otherwise it will cause burnout.
15. The remote control transmitter should keep the casing well, to prevent the phenomenon of extrusion, vibration, falling, and water inflow. Pay attention to check the battery voltage and replace it if necessary. When the remote control distance is too close, the battery should normally be replaced. The battery model is KC12V-23A. The remote control should try to avoid the source of electromagnetic interference.
16. The type of the interface of the alarm probe output signal should be the relay output interface. The supply voltage should be 12-15V DC, otherwise it cannot be directly powered by this controller. Probe power consumption should be ≤ 100 mA. According to the situation on the site can be equipped with more than one probe (usually 1 - 2 is appropriate), multi-probe parallel connection. Probes. Avoid the influence of other heat sources or direct light. Use a rain cover at the top.
Modern sweeping linear style. the towel racks are finished in high quality white finish. The only place to dry your towels neatly. It is not just about functionality and design, but also quality: this rail will last for years to come.
Towel Rack,Hand Towel Holder,Towel Bar,Towel Hanger
Kaiping city Pinsen Sanitary ware Co.,Ltd , https://www.corpthen.com